AcuRite 00607 Specifiche Pagina 146
- Pagina / 224
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Southwestern Industries, Inc.
ProtoTRAK SMX K2, K3, K4 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual
142
Caution!
After the readerhead is attached to the readerhead mounting bracket, do not move the
machine axis until the shipping brackets are removed. This will break the readerhead.
Caution!
Do not pinch the wires.
3. Mount the scale to the table:
• Transfer the center hole first to use as a pivot point.
• Align the scale so that it is within 0.005” end to end.
• Transfer the holes on the ends and install the screws.
• Re-check the alignment.
4. From the readerhead on the scale, remove the nameplate, shield and wires so that the
mounting holes are accessible.
5. Attach the readerhead to the readerhead mounting bracket:
• There are jackscrews on the readerhead to compensate for some gap between the
readerhead and the readerhead mounting bracket.
• Before tightening the readerhead to the bracket, there must be a .002 - .003” gap
between the readerhead mounting bracket and the jackscrews. Tightening the mounting
screws will eliminate this gap.
6. Replace the wires, shield and nameplate.
7. Remove the shipping brackets that fix the readerhead to the scale for shipping.
7.7.2 Y Axis Scale Installation
1. Install the readerhead mounting bracket to the side of the saddle.
Note: Once the readerhead mounting bracket is installed, position the scale and mounting spar
assembly in position in order to determine the amount of spacers needed for the mounting spar. Also
ensure that the scale is long enough for the saddle travel.
2. Transfer the mounting spar holes to the saddle and mount it.
Note: the mounting spar must be parallel to the Y-axis travel within .005” end to end both horizontally
and vertically. Use spacers and shims as necessary.
3. Slide the scale into the mounting spar and fasten.
Note: the rest of the installation is the same as for the X-axis, Steps 5 through 7.
- ProtoTRAK 1
- K2, K3, K4 & 1
- Retrofit 1
- Fax 310.764.2668 2
- Fax 310.886.8029 2
- Table of Contents 3
- 1.0 Safety 6
- 1.3 Safety Precautions 8
- 2.0 Installation 11
- 2.2 Uncrating 13
- 2.5 Machine Specifications 15
- 2.9 Cleaning 21
- Placement of Levels 22
- 2.11 Electrical Connection 23
- Not for retrofit 24
- Figure 8 24
- Figure 9 25
- Figure 9-1 26
- Figure 11 29
- Transformer Option Schematic 29
- 2.14 Cable Interconnections 31
- Figure 14 33
- Pendant - Right Side 33
- P/N: 24000-1 33
- Figure 15 34
- Cable Connection Diagram 34
- Non-Spindle Control 34
- Figure 16 36
- 2.15 Lubrication 37
- 2.15.2 Head Lubrication 39
- • X = 1.318 40
- • Y = 1.318 40
- Figure 18 41
- Euclid Block 41
- 3.1.1 Poor Finish 42
- 3.1.2 Circles Out of Round 43
- 3.2.1 Run Away Axis 45
- 3.2.2 Slow Down Axis 46
- 3.2.3 Axis Will Not Jog 46
- 3.2.5 Vibration in Motion 47
- 3.2.6 Searching Axis 48
- 3.3.1 Display Blanks 49
- 3.3.3 Keyboard Lockup 49
- 3.3.4 Fault X or Y 49
- 3.3.8 System Shuts Off 51
- Machines Only) 52
- Direction 56
- 3.5.4 Head Noise 59
- 4.0 Diagnostics 61
- 4.1.3 Lubrication 62
- 4.1.4 Machining Set-Up 62
- 4.1.4.1 Spindle Speeds 63
- 4.1.4.2 Feedrates 63
- 4.4 Motor Diagnostics 66
- 4.5 Servo Driver 67
- 4.6 Glass Scales 68
- 4.7 TRAK Sensors 69
- 4.8 Electrical 71
- 4.8.4 Cable Connections 72
- Figure 19 73
- Electrical Box Schematic 73
- Figure 20 75
- Figure 21 76
- LEDs on Spindle 76
- Control Board 76
- 4.9 Service Codes 77
- 4.9.1 Software Codes 77
- 4.9.2 Machine Set-up Codes 78
- 4.9.3 Diagnostic Codes 81
- & Maintenance 84
- Figure 22 85
- Figure 23 86
- Figure 24 88
- Flash Disk Replacement 88
- Flash Disk Parts List 88
- Flask Disk Replacement 88
- 5.1.6 TRAK Sensor 89
- Figure 25 90
- M5 Base Mounting 90
- Figure 26 91
- TRAK Sensor Mounting 91
- Figure 27 92
- K Mill Sensor Assembly 92
- Z-Axis Glass Scale Assembly 95
- Figure 29 96
- Glass Scale Alignment 96
- 5.1.8 Power Drawbar 97
- Figure 30 98
- Power Drawbar Assembly 98
- Figure 31 100
- X-Axis Drive Assembly 100
- Figure 33 105
- Spindle Motor Wiring 105
- Figure 36 107
- Figure 37 109
- Figure 38 110
- 5.2 Maintenance 111
- Figure 39 111
- Table Gib Adjustment 111
- Figure 40 112
- Table Gib Screw 112
- Figure 42 114
- Figure 43 115
- Calibration Set-Up 115
- 5.2.3.2 Tramming the Head 117
- Side-to-Side Alignment 117
- Back to Front Adjustment 118
- 5.2.4 Limit Switch Option 119
- 6.0 Retrofit Installation 121
- 7.0 Installation Procedures 123
- X-Axis Ball Screw 125
- Figure 51 127
- Figure 55 133
- Figure 56 136
- X Motor Mounting 136
- Figure 58 141
- Z-Axis Glass Scale Assembly 141
- Figure 59 142
- X Bracket Installation 142
- Figure 60 143
- Y Bracket Installation 143
- Figure 61 144
- 148
- 7.9 System Interconnection 150
- Figure 66 151
- Figure 68 156
- & Covers Assembly 156
- Figure 68-1 158
- Ball Screw Module 158
- P/N 24250 158
- Parts List Ball Screw Module 159
- 8.4 Lagun Z Axis Cutout 160
- Figure 69 160
- 9.2 Warranty 161
- 9.3 Replacements 163
- Figure 100 164
- Figure 104 169
- Pulley Pinion Sub-Assembly 169
- P/N: 20697-4 169
- Figure 105 170
- Lower Vari-Disc Sub-Assembly 170
- P/N: 20697-5 170
- Figure 106 172
- Upper Vari-Disc Sub-Assembly 172
- P/N: 20697-6 172
- Figure 109 176
- Bottom Housing Assembly 176
- Figure 110 180
- P/N: 20698-1 180
- Parts List 192
- Head Top Assembly - 24692 192
- Figure 120 194
- Hi-Low Shift Clutch 194
- Sub-Assembly 194
- P/N: 20778-2 194
- Figure 121 196
- Hi-Low Shift 196
- P/N: 20778-3 196
- Figure 125 202
- Speed Change Handwheel 202
- P/N: 20778-7 202
- Figure 127 204
- Lower Head Assembly 204
- Figure 128 208
- Worm Gear Cradle 208
- P/N: 20779-1 208
- Figure 134 214
- K2/K3 Base Machine P/N 20785 214
- Figure 135 218
- K4 Base Machine P/N 26900 218
- Parts List - K4 Base Machine 219
- Figure 136 221
- P/N: 23470-220 or 23470-440 221
- Figure 137 222
- P/N 23470-220 or 23470-440 222
- TRAK Warranty Policy 224
Prodotti e manuali riguardandi Stazioni metereologiche AcuRite 00607
Stazioni metereologiche AcuRite 614 Manuale Utente
(457 pagine)
(457 pagine)
TakeMS Kartenleser Benutzerhandbücher
Beginnend mit T
| Modelle | Dokumententyp |
|---|---|
| TMS-CR-MF12R | |
| TMS-CR-MOB1 | |
| TMS-CR-TFL1 | |
| TMS-CR-TFL1B | |
| TMS-CR-TFL2B | |
| TMS-CR6412 | |
| TMS-CR6413 | |
| TMS-CRE-M1B | |
| TMS-CRE-M1S | |
| TMS-CRE-P1B |
© 2020, manymanuals.it. Tutti i diritti riservati | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale